DIYSwede
Τα περιεχόμενα μου
Όλα τα μηνύματα
Κριτικές
Σχόλια
Απαντήσεις
Ερωτήσεις

Όλα τα μηνύματα

DIYSwede 08/01/2019
This seemed so good I ordered 2 sets! But then: -Slow transport, no tracking for three weeks, and when the package finally arrives, content isn't what I ordered - only one set as per the order, then another set with only six (instead if 12) holesaws, only bigger up 'til 65 mm. Might as well try the biggie on a 15 mm aluminum sheet - it went fantastic! My lathe complained at 220 rpm when feeding in this 65 mm hole cutter, but it went thru in a jiffy, with better side finish than with ordinary Starrett HSS saws of equal dia. This is due to that this cutter IS NOT mounted on a threaded mandrel like the Starretts, this one is in one piece per size: consistency guaranteed!
Σετ 12 κομματιών τρυπάνι με σιγκσιούρα 15mm-50mm Drillpro για κοπή ξύλου μετάλλου
US$33.99 US$29.99
7
Συστάσεις
Σχόλια (0)
DIYSwede 13/04/2019
Excellent value for the low price! These work great if you just respect the following: Don't run at high revs - use a hi-torque cordless with a brake. Repect the short length drill part - don't try to thread anything thicker than the drill's free length. These drill diameters are somewhat small, achieving a really deep thread depth, that'll be tough on the tap, your drill and your wrists (if handheld). I'll personally only use them on cast iron, cast aluminium and mild steel. I'd never ever let the smaller ones bottom out into the purported "deburr/ countersink" feature - jeez - Marketing BS. For heavier alloys I'd still use predrilling to lesser thread percentage and continue using my old straight-fluted taps.
Σετ 6 συνδυασμένων τρυπανιών και καρφίων HSS 6542 M3-M10 με επίστρωση τιτανίου 1/4 ιντσών μετρικής εξάγωνης άκρης για κόψιμο μεσινέζας ελληνικού μητρώου και τα επιφανειακά εξοπλισμούς.
US$5.99 US$9.99
4
Συστάσεις
Σχόλια (0)
DIYSwede 15/02/2019
Nice, high-precision and finely ground HSS Metric tap set. Recommended!
Σετ τρυπανιών 7τμχ M3-M12 HSS Nitriding Επικαλυμμένο Μετρικό Δεξιόστροφο Ελίτσα Βίδας
US$17.31 US$17.99
2
Συστάσεις
Σχόλια (0)
DIYSwede 16/02/2019
Excellent quality Metric HSS taps with cleanly ground cutting edges and flutes at a very good price. This set covers almost all coarse threading jobs in my workshop. Clean, nice threads and more easy to hand thread than my old uncoated taps.
Σετ τρυπανιών 7τμχ M3-M12 HSS Nitriding Επικαλυμμένο Μετρικό Δεξιόστροφο Ελίτσα Βίδας
US$17.31 US$17.99
2
Συστάσεις
Σχόλια (0)
DIYSwede 07/12/2018
Arm and holder of nice workmanship and consistent operation, magnetic base leaves a bit to desire: Roughly milled V-slot (see pic): improperly ground and deburred. Not even perpendicular between the bottom/ back surfaces who arent perfectly straight either. Pretty weak magnetic holding force, but small and good enough for nice operation on my 7 x14" lathe, where a longer arm would be cumbersome. So if you, like me, will invest half an hours work grinding and honing ii to finishing it off by yourself, it's still a perfectly good holder at a bargain!
Εργαλείο Mini Flexible Magnetic Base Holder της DANIU για το Τεστ Δείκτη Επιλογής
US$19.99 US$23.99
3
Συστάσεις
Σχόλια (0)
DIYSwede 24/07/2020
Excellent value for money for this temp-controlled soldering iron! Bonus for the plentiful of differnet tips.
39Pcs 110V 220V 60W Ξύλο Καυστήρα Συγκόλληση Εργαλείο Εργαλεία Σετ Πυρογραφία Kit Συμβουλές
US$30.02 US$31.99
1
Συστάσεις
Σχόλια (0)
DIYSwede 15/07/2020
Great value-for-money honing disks, fast delivery and adequately packed.
3 τμχ 6 ιντσών 120 400 1200 Χαλίκι Diamond Wheel Diamond Diamond Grinding Diamond
US$28.59 US$31.99
1
Συστάσεις
Σχόλια (0)
DIYSwede 14/11/2018
Easy to setup, handle and read, but almost toy-looking IR thermometer. For the price, it's a bargain, and it even includes an English manual. Takes half a second before reading is shown in F or C (not K), and the IR reading angle is 3,6 degrees, or 30 mm dia circle at half a metre. Nice feature is that you can enter the emissivity of chosen material. Repeatabilty claimed to be 1% of reading. Overall: Good accuracy for the money, the low price and it's cheap, kiddie look makes me use it in the foundry/ workshop without hesitation.
HoldPeak HP-1300 -50-1300℃ IR Laser Thermometer Temperature Gun
US$58.89 US$61.99
2
Συστάσεις
Σχόλια (2)
DIYSwede 28/11/2018
Nicely built, good results for this power pack. these small fins get pretty hot, so put it in ventilated metal box. Pic shows 100W @ 12 VDC in, where fins still could be touched
Ρυθμιστής ταχύτητας κινητήρα DC με PWM πλάτους παλμών 6-90V 15A 1000W Διακόπτης ρύθμισης ταχύτητας
US$6.99 US$13.99
3
Συστάσεις
Σχόλια (0)
DIYSwede 23/01/2018
Got myself two of these, both with a plastic pump/headcap and nozzle. Good enuff for my needs for way lube and thread cutting oil, not too unwieldy as it's not that big/ heavy - but not to small to require constant refills either.
250ml Χύσιμο Δοχείο λαδιού Hard Tube Soft Tube Oil Gun
US$8.79 US$9.99
1
Συστάσεις
Σχόλια (0)
DIYSwede 14/12/2018
Looking cheap and not worth its money... Not entirely of stainless - just the ruler (which unfortunately is poorly milled and ground). The three heads are of cast aluminium (stated nowhere on the page), and really only roughly machined too. The two scale marks are off and the center finder angle less than 90 degrees (see pics). To fix this for my intended workshop use there would be a few hours work of grinding, fitting and upgrading, but then the question of reliability over time arises... Surprising and disappointing as all my previous Daniu buys has been of good craftmanship and really prizeworthy tools.
DANIU 12inch Square Ruler Ρυθμιζόμενο από ανοξείδωτο χάλυβα εργαλείο γωνίας συνδυασμού
US$16.79 US$26.99
3
Συστάσεις
Σχόλια (1)
DIYSwede 16/02/2019
Inexpensive, accurate and portable thermometer for checking melts in my aluminium/ brass electric foundry. In being light and small, it has also been used for checking my deep freezers thermostat, bath and air duct temps and even a sunday steak inner temp.
TM902C LCD K Type Thermometer Temperature Meter Probe Thermocouple Probe
US$16.16 US$16.99
1
Συστάσεις
Σχόλια (0)
DIYSwede 16/08/2018
Provided with an easy-to-follow English manual this tiny (40 x 40 mm front panel) controller has enough user modifiable parameters to steer my 2 x 230 VAC, 5 kW DIY foundry/ hardening oven, even though I had to add another +1300 C K-type element (as the provided thermocouple maxes out at 300C). The solid state relay can handle with a heat sink 40 amps, even though my oven will just pull some 13 A. The 25 metres of 1,2 mm Kanthal A-1 Wire (actually mfg'd some 75 mi from my place) was more expensive here than this entire regulator kit from abroad... Amazing!
100-240V 40A Digital PID Temperature Controller SSR K Thermocouple Sensor
US$16.92 US$20.16
2
Συστάσεις
Σχόλια (0)
DIYSwede 26/06/2019
Tool post mill to-be, powered by a 250 W 48 V DC motor. Nicely machined, tight fit for the bearings and spindle, 120 XL belt. Ordered a few of each at these ridiculous prizes. The 10T wheel will be mounted on my mini lathe's motor, I'll just cut a 30T Delrin gear, order another, longer XL belt to get a 3:1 motor reduction. This instead of buying a XL kit on Ebay for a hundred bucks (incl shipping)...
Machifit No Σετ Τρυπανιών Αξεσουάρ Μικρού Τόρνου Ζώνη Κοπής JTO/B10/B12/B16
US$9.88 US$9.99
1
Συστάσεις
Σχόλια (0)
9 κομμάτια ER32 Ακρίβειας Ροδέλα Ελατηρίου για CNC Τόρνο και Φρεζάρισμα
US$52.99 US$63.99

Ερ: So I chose these collets to work with an MT 3 chuck, also from Banggood. Basically, they are INCOMPATIBLE. For example, choose 8 mm collet and fit into chuck. This compresses the collect enough so its impossible to then fit an 8mm bit. Also, without even fiiting the milling bit, Only 1 and a bit turns can be made with the collect nut. Anyone else had this issue?

Ερώτηση από wetlume επί 2018-12-15 06:23:37

DIYSwede Excuse me for perhaps stating the obvious: -Did you really press the collet into the ring nut first, and then screw them both lightly into the chuck, before fitting the 8 mm bit and final tightening?

2019-07-04 03:29:16 Βοηθητικός (0)
υποβάλλουν
Απαντήσεις (2)
DIYSwede 16/02/2019
Excellent craftmanship and performance with near zero runout at a very good price. Nice, small point makes end facing simple. Only minus is that the protruding MT2 small end reduces my quill travel 1/2", but I guess that will be cut/ ground off one of these days.
MT2 Κέντρο ζωντανής τορνοκοπτικής άξονας Morse Taper CNC εργαλείο 0,000197 ίντσα Ακρίβεια
US$35.79 US$37.99
0
Συστάσεις
Σχόλια (0)
DIYSwede 13/04/2019
Good quality boot covers at a discount, nicely cut and sewn, fitted with elastic sole band and wide Velcro strips, Tip: Waterproof/ condition them with "DIYSwedes Suede-goo": Melt 55% beeswax, add 45 % ATF, let cool and apply lightly. Use stiff brush to condition/ clean them - never wash them!
1Pair 8.3 ίντσες δέρμα αγελάδας δέρμα συγκόλλησης πόδια κάλυμμα μανίκια ανθεκτικά στη φλόγα ασφαλή γάντια
US$14.99 US$17.99
0
Συστάσεις
Σχόλια (0)
DIYSwede 13/04/2019
Good quality welders sleeves at a discount, nicely cut and sewn, fitted with black synthetic cuffs, so use long gloves to cover these. Tip: Waterproof/ condition them with "DIYSwedes Suede-goo": Melt 55% beeswax, add 45 % ATF, let cool and apply lightly. Use stiff brush to condition/ clean them - never wash them!
Δερμάτινα μανίκια συγκόλλησης από δέρμα αγελάδας με γάντια από ελαστική μανσέτα
US$9.62 US$12.83
0
Συστάσεις
Σχόλια (0)
DIYSwede 28/11/2018
Small but rugged little PWM regulator, easy to box and conceal. Note: It won't zero its output completely (it gives 10-100% output), and the fins get darned hot when running at high amps - so a vented metal box will probably be a good choice.
DC 9V έως 50V 10A Stepless Ρυθμιζόμενη μονάδα PWM DC Motor Controller Speed Module με κουμπί
US$9.19 US$9.99
0
Συστάσεις
Σχόλια (2)

Είστε ο ειδικός, μπορείτε να βοηθήσετε;

Σας προσκαλούμε ειλικρινά να εγγραφείτε στο email πρόσκλησης απάντησης!

Εάν εγγραφείτε, θα σας προσκαλέσουμε μέσω email για να απαντήσετε σε ερωτήσεις που έχουν οι άνθρωποι σχετικά με τα προϊόντα. Με την εγγραφή σας] θα κερδίσετε επίσης το "Χρήσιμο σήμα "! Μπορείτε να διαγραφείτε ανά πάσα στιγμή στη σελίδα ρυθμίσεων απορρήτου.

Βοηθήστε τους άλλους και γίνετε πιο ευτυχισμένοι!

  • Εγγραφείτε

Σχετικά με τα σήματα

Τα σήματα σχετίζονται με την κοινότητα και οι χρήστες κερδίζουν σήματα δημιουργώντας ποιοτικό περιεχόμενο, ολοκληρώνοντας αποστολές ή συμμετέχοντας σε ειδικές δραστηριότητες. Συγκεκριμένα άτομα θα έχουν επίσης το δικό τους αποκλειστικό σήμα.
Διευθύνων σύμβουλος

Το CEO Badge ανήκει μόνο στο αφεντικό του Banggood.

Τα σήματα που μπορείτε να κερδίσετε έρχονται σύντομα
  • Εντάξει

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • Εντάξει

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe