This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

παραλήφθηκε σε καλή κατάσταση

received with good condition

παραλήφθηκε σε καλή κατάσταση

Ακριβώς όπως περιγράφεται

Just as described

Ακριβώς όπως περιγράφεται

motore come da descrizione

motore come da descrizione

motore come da descrizione

Εξαιρετικά

excellent

Εξαιρετικά

As expected, this was a replacement for a Phoenix 1600

As expected, this was a replacement for a Phoenix 1600

As expected, this was a replacement for a Phoenix 1600

The motor received 2 weeks after ordering - very fast delivery. Not tested yet. Only packaging was quite poor - only two thin plastic bags (no bubble foil or so). Sp I trust the motor will be O.K. and working properly.

The motor received 2 weeks after ordering - very fast delivery. Not tested yet. Only packaging was quite poor - only two thin plastic bags (no bubble foil or so). Sp I trust the motor will be O.K. and working properly.

The motor received 2 weeks after ordering - very fast delivery. Not tested yet. Only packaging was quite poor - only two thin plastic bags (no bubble foil or so). Sp I trust the motor will be O.K. and working properly.

Πολύ καλά

VERY GOOD

Πολύ καλά

ottimo

ottimo

ottimo