This project was enjoyable to build but it didn't function properly on completion. The first issue is that the circuit board power trace connects to both throws of the switch. This means that the switch is constantly turned on. To fix this cut the trace between the two outter pins of the switch. See picture below. The second problem that was encountered was that all the lights lit and there was no speed control. This was fixed by adding (2) 100 nF decoupling capacitors. One for the CD4060 and one for the Music circuit. Connect them between the Vcc and the Ground on each device. See picture below. This solved the oscillation problem and allowed control of the lights. The final problem was not resolved as the music chip only played one continuous note. It didn't matter much as the price was right and I had fun putting it together and trouble shooting the problems.

This project was enjoyable to build but it didn't function properly on completion. The first issue is that the circuit board power trace connects to both throws of the switch. This means that the switch is constantly turned on. To fix this cut the trace between the two outter pins of the switch. See picture below. The second problem that was encountered was that all the lights lit and there was no speed control. This was fixed by adding (2) 100 nF decoupling capacitors. One for the CD4060 and one for the Music circuit. Connect them between the Vcc and the Ground on each device. See picture below. This solved the oscillation problem and allowed control of the lights. The final problem was not resolved as the music chip only played one continuous note. It didn't matter much as the price was right and I had fun putting it together and trouble shooting the problems.

This project was enjoyable to build but it didn't function properly on completion. The first issue is that the circuit board power trace connects to both throws of the switch. This means that the switch is constantly turned on. To fix this cut the trace between the two outter pins of the switch. See picture below. The second problem that was encountered was that all the lights lit and there was no speed control. This was fixed by adding (2) 100 nF decoupling capacitors. One for the CD4060 and one for the Music circuit. Connect them between the Vcc and the Ground on each device. See picture below. This solved the oscillation problem and allowed control of the lights. The final problem was not resolved as the music chip only played one continuous note. It didn't matter much as the price was right and I had fun putting it together and trouble shooting the problems.

muito bem feito funcionou direitinho como nu anuncio bom de montar qualquer um monta

muito bem feito funcionou direitinho como nu anuncio bom de montar qualquer um monta

muito bem feito funcionou direitinho como nu anuncio bom de montar qualquer um monta

When first assembled the sound was badly garbled and for the most pat the tune was not distinguishable. If you want it to work better cut the trace indicated in the picture and install a 1K resistor across the cut.

When first assembled the sound was badly garbled and for the most pat the tune was not distinguishable. If you want it to work better cut the trace indicated in the picture and install a 1K resistor across the cut.

When first assembled the sound was badly garbled and for the most pat the tune was not distinguishable. If you want it to work better cut the trace indicated in the picture and install a 1K resistor across the cut.

great!!! thank you.

great!!! thank you.

great!!! thank you.

All OK. Only 1 week to New Zealand. I have stoped using Aliexpress because delivery takes months and often never arrived.

All OK. Only 1 week to New Zealand. I have stoped using Aliexpress because delivery takes months and often never arrived.

All OK. Only 1 week to New Zealand. I have stoped using Aliexpress because delivery takes months and often never arrived.

Ωραία

Good

Ωραία

Like describe

Like describe

Like describe

Habe bereits zwei von diesen Bausätzen verarbeitet. Eine sehr gute Lötübung mit abschließender Funktion zur Erfolgskontrolle. Spoiler: Die Drahtbrücke hinter dem Chip PX088A, so wie auf dem Bild unter Produktdetail dargestellt führte bei mir zur Fehlfunktion und wurde getrennt. Aber auch dies war eine gute Übung zur Fehlersuche. 🙂

Habe bereits zwei von diesen Bausätzen verarbeitet. Eine sehr gute Lötübung mit abschließender Funktion zur Erfolgskontrolle. Spoiler: Die Drahtbrücke hinter dem Chip PX088A, so wie auf dem Bild unter Produktdetail dargestellt führte bei mir zur Fehlfunktion und wurde getrennt. Aber auch dies war eine gute Übung zur Fehlersuche. 🙂

Habe bereits zwei von diesen Bausätzen verarbeitet. Eine sehr gute Lötübung mit abschließender Funktion zur Erfolgskontrolle. Spoiler: Die Drahtbrücke hinter dem Chip PX088A, so wie auf dem Bild unter Produktdetail dargestellt führte bei mir zur Fehlfunktion und wurde getrennt. Aber auch dies war eine gute Übung zur Fehlersuche. 🙂

Recebido, completo OK

Recebido, completo OK

Recebido, completo OK

good product

good product

good product