xman12
Τα περιεχόμενα μου
Όλα τα μηνύματα
Κριτικές
Σχόλια
Απαντήσεις
Ερωτήσεις

Όλα τα μηνύματα

xman12 25/05/2022
I test this inverter with only 2050W because my strong batteries are still on the way. To make it short, I think that this Inverter can deliver not more than 8000W AC. The reason is that I found the same Inverter from another source and they offer only 8KW and 12KW Inverters! Also Inside there are 4 x 50Amp DC Fuses. Given you have an 53V Battery and the maximum of 200Amp you get 10,6Kw DC Power, if you then add the efficiency lets say 86% you get only 9,116KW AC Power. If you than have the case that the Battery Voltage drop to 40V (2,5V per cell 16SLiFePo4) you get the maximum of 8Kw DC and 6,9Kw AC This is OK for this price but you should think about it if you consider to use the full advertised 10Kw, It is only the DC Power not the useable AC Power. So it look like that the Seller was relabeling the Inverter from 8Kw AC to 10Kw DC. This is no big problem for me because I only need 5KW at max, so I bought the "10KW" Inverter to get enough permanent poweroutput. I take an look inside but do not examine all the Power Mosfet. It looks like that the DC Side uses 2x of eleven Kia KNP9120A Mos. And some of murata diodes for the 400V side. At the AC Side you can not see anything without remove the holders from the Mosfet or IGBT. I changed the Cu bar connection to the DC clamps with extra washers, because they pulled the PCB Upside. You can see it on the pictures.
Μετατροπείς ηλιακής ενέργειας με καθαρή ημιτονική κύματα 12/24/48V σε 220V με την εμπειρία της Excellway στα 10.000W μέγιστης ισχύος σε συχνότητα 50Hz και ψηφιακή οθόνη για την παροχή ενέργειας αντιστροφέα.
US$69.99 US$79.99
28
Συστάσεις
Σχόλια (13)
xman12 21/04/2023
!!!!! Use "Start G code" in your Printer settings: G28 ; homing all axes (allready in the settings, but after that you have to use) M420 S1 ; Use the stored level bed Information!!!!! If you do not do this the printer will scratch the Bed at first try you print your own Model!! The test cube on the USB Stick use this commands in his Gcode before printing. The Problem is the Cura slicer, there will be no M420 S1 command at default. You have to add this by yourself! Now I know why my Ender 3 V2 never was using "Autobedleveling values" by default, I switched it on in the Menue manually, everytime before I print something on it. Now I know it better. At Atillery: Its not fair to new users to scratch there Printerbed's by intentionally!!! The Firmware should use the M420 S1 command by itself at default and not only by Gcode! This ist very Bad practice by an Manufacturer not only Atillery but also Creality! So I have to give only 4 Stars, not because of the Printer but the Manufacturer's practice.
Κιτ εκτυπωτή 3D Artillery® X2 με μεγάλο μέγεθος εκτύπωσης 300*300*400mm,υποστήριξη επανέναρξης εκτύπωσης και ανίχνευσης τελειωμού με διπλό άξονα Z/αφής TFT οθόνης
US$299.00
3
Συστάσεις
Σχόλια (1)
xman12 18/05/2021
Hello, I tested this DIY weather station. I get it working like one the picture. The problem with this is the software. I downloaded the "esp8266-weather-station-master" at Github. This is only an software to show the 3-day weatherforecast data from OpenWeathermap.com on the Display. You first need to open an account at openweather to do that. You can also send data to an open sensor network (thingspeak) but no one wants this in any case. I want to show my own Weatherdata direct on the display without the long way round to the Internet and back to the ESP. (I understand that it will work in this way, may be I am wrong?) All Sensors has no funktion out of the box and their data will not showed on the display, you have to program it all by yourself! I espected that the Manual shows the way to read out all the sensors and show the data on the Display, but nothing... The manual should make it possible to: 1. Weatherforcast for eg. openweathermap.org 2. show one page with local weather data from the sensors attached to the ESP. 3. and optional, sending of weatherdata to an open sensor network. There are also some problems with different and wrong libraries I was allready able to read out all the sensors one by one for testing. If you want to show their data on the Oled you have to read out the sensor data and extend the esp8266 weather station program code by yourself. But it use other libraries than the other programs to read out the sensors, so you have to change the program code that it will fit to the libraries which will used in the openweather sketch. This is not very good for beginners.
Σύνολο Σταθμού Καιρού AOQDQDQD® ESP8266 με Αισθητήρα Θερμοκρασίας, Υγρασίας, Πίεσης Ατμόσφαιρας και Οθόνη 0.96 για το Arduino IDE IoT Starter
US$13.99 US$20.99
1
Συστάσεις
Σχόλια (1)

xman12 Donot work with SDR console, is not able to find the USB device which will work allready with HDSDR and SDRUNO at the same computer.

belean 02/02/2022
Work perfectly with SDR Console v3.0.24 software and Multiband End-fed 80-10m antenna. https://www.youtube.com/watch?v=0jFCf5OHYJ8&ab_channel=BeleanCristianPetru
Δέκτης SDR απλοποιημένης έκδοσης RSP1 Δέκτης λειτουργικότητας λογισμικού ορισμένος από τον χρήστη για την αεροπορία χωρίς RTL
US$31.04 US$20.99
3
Σχόλια (1)
Δέκτης SDR απλοποιημένης έκδοσης RSP1 Δέκτης λειτουργικότητας λογισμικού ορισμένος από τον χρήστη για την αεροπορία χωρίς RTL
US$31.04 US$20.99

Ερ: It do not work in CB Area 26,9Mhz and above and also do not work below 433Mhz Area, spezial in the 400-406Mhz for weather Baloons it is useless.

Ερώτηση από xman12 επί 2023-04-24 07:48:50
υποβάλλουν
Απαντήσεις (0)

xman12 Eskönnte sein dass dieser für die Steuerung des Speedlimit ist, daher als Ersatz für Turbo ECO. Ich bin nicht sicher

eurofilgo 20/03/2023
A harmadik vezeték funkcióra még mindig nem kaptam választ. Valószínű "hadi " titok.
Ασύρματη συσκευή κλειδώματος για ηλεκτρικά σκούτερ κάτω από 60V ES19 TI30 ES18P T30 SR10 ES18 Lite L8S PRO ES10P L6 Pro
US$9.99 US$54.99
3
Σχόλια (2)
xman12 25/04/2022
Hello, I buy 20AWG and get 37,7Ohm / Km resistance, not so great but OK. May be an measuring difference. It should be arround 34,5Ohm.
Μπλε 3 M 8/10/12/14/16/18/20/22/24/26 AWG Silicone Wire SR Wire
US$10.38 US$10.99
0
Συστάσεις
Σχόλια (0)
xman12 14/06/2021
Seems to work, I flashed the new Firmware to my Ender 3 V2 and mounted the BL-Touch sensor and started the Autolevel process successful. I did not test now how much is the effect on a new 3d print yet, but I will test in the next time.
Creality 3D® Ender-3 V2 Αναβαθμισμένο Σετ του αισθητήρα αυτορύθμισης BL Touch για εκτυπωτή 3D
US$54.27 US$59.99
0
Συστάσεις
Σχόλια (2)

xman12 I had some bad experience with this Sensor but the reason is the creality Firmware. If you "live set" the Z- offset during printing you should not do this! if you allready set an value and want to change it during printing, let it be!!! The Firmware do not change the printinghead by the delta but by the absolute value! So if you change the value by -0,05mm eg. from -2,2 mm to -2,25mm the head moves !!!-2,25mm!!! and scratches the glasbed. Also I had some Bltouch error where the glasbed bend the Pin of the BlTouch because it do not retract the Pin sometimes. I changed to JYer Firmware and never go back to creality's Firmware.This was my Experience with Firmware "Ender-3 V2-Marlin-2.0.1-HW-4.2.2-mainboard-V1.1.2-Compatible with BLTouch and filament detection"

xman12 14/06/2021
Seems to work, I flashed the new Firmware to my Ender 3 V2 and mounted the BL-Touch sensor and started the Autolevel process successful. I did not test now how much is the effect on a new 3d print yet, but I will test in the next time.
Creality 3D® Ender-3 V2 Αναβαθμισμένο Σετ του αισθητήρα αυτορύθμισης BL Touch για εκτυπωτή 3D
US$54.27 US$59.99
0
Σχόλια (2)
Δοκιμαστής πυρηνικής ακτινοβολίας με υψηλή ακρίβεια 0.05uSv-50mSv Δοκιμαστής ραδιενέργειας με ενσωματωμένη μπαταρία TFT2.0 Έγχρωμη οθόνη εμφάνισης Λειτουργία συναγερμού
US$64.99 US$99.99

Ερ: Does this have a CE-certificate?

Ερώτηση από BG121461441 επί 2022-04-01 12:57:26

xman12 Mein Gerät hat kein CE Zeichen, wofür auch? Selbst wenn eines aufgedruckt ist hat das keinerlei Bedeutung. Jeder kann das CE Zeichen aufkleben aber versuchen sie mal den chinesischen Hersteller dafür zu belangen wenn das Gerät doch nicht CE-Conform ist.

2022-04-03 10:41:05 Βοηθητικός (2)
υποβάλλουν
Απαντήσεις (2)
xman12 03/04/2022
Es scheint zu funktionieren, ohne Vergleichsgerät kann ich die Genauigkeit nicht abschätzen. Leider war das Gerät vor der Lieferung wohl noch im Standbymodus so das der Akku komplett entladen war, soweit das zuerst kaum ein Ladestrom in den Akku geflossen ist. Das sollte der Hersteller unbedingt ändern weil es möglich ist das der Akku, wenne r an der untersten Spannungsgrenze gelagert wird auch geschädigt werden könnte. -Zum kompletten Auschalten muss die obere Taste sehr lange gedrückt werden bis das Gerät "Shutdown" anzeigt. -Die Sprache wird auf Englisch umgeschaltet indem man in Zählrichtung in Menue 6 geht und den zweiten Eintrag im Menue umschaltet. ( zweite reihe ganz rechtes Menue)
Δοκιμαστής πυρηνικής ακτινοβολίας με υψηλή ακρίβεια 0.05uSv-50mSv Δοκιμαστής ραδιενέργειας με ενσωματωμένη μπαταρία TFT2.0 Έγχρωμη οθόνη εμφάνισης Λειτουργία συναγερμού
US$64.99 US$99.99
0
Συστάσεις
Σχόλια (0)
xman12 27/03/2022
Ich habe mit Amateurfunk nur am Rande zu tun bin aber recht begeistert von dem Gerät. Dafür das ich nur eine ca 2,7m lange Antenne verwende liefert es ein gutes Signal. Getestet habe ich schon DAB+ FT8 USB LSB AM und UKW-FM Natürlich hat das RSP1 jetzt keinen automatischen Eingangsfilter umschalter wie die komplexere Version, da ich aber nicht ständig zwischen den Bändern hin und her schalte kann ich damit leben die Antenne jeweils umzustecken.
Δέκτης SDR απλοποιημένης έκδοσης RSP1 Δέκτης λειτουργικότητας λογισμικού ορισμένος από τον χρήστη για την αεροπορία χωρίς RTL
US$31.04 US$20.99
0
Συστάσεις
Σχόλια (0)
Δοκιμαστής πυρηνικής ακτινοβολίας με υψηλή ακρίβεια 0.05uSv-50mSv Δοκιμαστής ραδιενέργειας με ενσωματωμένη μπαταρία TFT2.0 Έγχρωμη οθόνη εμφάνισης Λειτουργία συναγερμού
US$64.99 US$99.99

Ερ: Hi. Does need changing an element within the mechanism by using it?

Ερώτηση από Kostarellosbill επί 2022-03-13 10:47:06

xman12 I don't know what you asking for. First, I have the radiation counter not there, it should last more than 2 weeks till it is there. Second, if you mean the GeigerMüller tube, look at the description of the radiation counter, there is listed which GM-Tube is used.

2022-03-15 11:35:28 Βοηθητικός (1)
υποβάλλουν
Απαντήσεις (4)
ΥΝΙ-Τ ΥΝι690Β 256*192 Pixel Θερμική καταγραφή υπέρυθρων -15~550°C Βιομηχανική Θερμική κάμερα Φορητό USB Θερμόμετρο υπερύθρων
US$319.99 US$699.00

Ερ: What is the closest focusing distance?

Ερώτηση από erberes επί 2020-11-03 09:21:12

xman12 I can't answer this because I do not get the device until now. I have to wait another week, I fear. Non posso rispondere perché non ho ricevuto il dispositivo fino ad ora. Devo aspettare un'altra settimana, temo. Sorry this is translated with google-translator :-)

2021-12-09 12:25:33 Βοηθητικός (1)
υποβάλλουν
Απαντήσεις (4)
Ασύρματη μονάδα ESP-01F ESP8285 Serial Port WIFI 8Mbit με κεραία IOT για έξυπνο σπίτι
US$4.92 US$10.99

Ερ: Does it work? Does it come with data? May be useless

Ερώτηση από BG439531495 επί 2021-11-19 02:07:31

xman12 I want to use this thing for an weathersensor later and I do not use it till now. Its is possible that you have to flash the Firmware first to use this product. For arduino you have to flash the ESP8266 NonOS SDK or ESP8266_RTOS_SDK.I bought many ESP01S moduls at amazon in the past and many of them were not flashed and not usable in the delivering state. After I flashed the ESP8266 NonOS SDK Firmware all of them are working. I have no experience with the ESP8266_RTOS_SDK, not tested it yet.

2021-11-19 09:57:25 Βοηθητικός (0)
υποβάλλουν
Απαντήσεις (1)
xman12 04/06/2021
My intend to purchase this „Aluminium Dual Gear/drive Extruder Kit“ was to go arround the problem with the filament is touching the x-axis motorspindle. Everybody should know that Ender do an design fault to mount the extruder stepper so close to the Z-Axis motorspindle! When its touching it the filament will transport the grease into the extruder. Since this filament-drive has smaller gears than the original, my hope was that the filament has an greater distance to motor spindle, but it were only arround 1,7mm more distance. Additionally you can’t use the second Air pipe holder because it is much to fat and touches also the motorspindle. So I still has to use an Silicon tube to protect the filament, so it fails in this manner. Because of the smaller gears you have some disadvantages over the original filament drive. 1. The pressure to the filament is greater per mm² ! So I fear that the PLA will break if the pressure will last for an longer time of standby time. I use the old spring to reduce the pressure by a little ammount. The better choice were to do not change the diameter but use the dual gears. 2. Since the gear on the steppermotor has fewer diameter you have to change the ammount of steps to an higher value. I messure the old diameter 10,96mm the new diameter is 7,45mm. Since the old steps should be 96 steps (I do not confirm that yet) I calculate 10,96mm/7,45mm * 96Step = 136,816 Steps other reviewers talk about 139Steps. 3. It can be but that is not sure or tested yet. Because of the much higher step count it is possible that the stepper motor is a little louder than before. Since I have silent steppers I expect not much difference. 4. You can’t use the blue transport wheel anymore to manually transport the filament to the extruder. The axle of the Steppermotor is to short to mount the wheel again. 5. I am not sure but I think that the second Gear has no ballbearing against the originally one.
Αναβαθμισμένος διπλός γρανάζι και γρανάζι διπλής οδήγησης αλουμινίου για εκτυπωτή 3D Creality CR-10 / CR-10S / CR-10S Pro / Ender-3 / Ender-3 Pro
US$24.24 US$25.99
1
Συστάσεις
Σχόλια (1)
Creality 3D® Ender-3 V2 Αναβαθμισμένο Σετ του αισθητήρα αυτορύθμισης BL Touch για εκτυπωτή 3D
US$54.27 US$59.99

Ερ: Not a wonder dosent work you BLtouch! when you send with wrong wired cable. red and blue changed... verify cable and the picture on manual. On manual all kabel 1:1. on my pakage red and blue changed... the nuzzle ram to the bed and z not stop after contact!!!!!! Why do you not check your hardware before you send thi to the user?

Ερώτηση από amle επί 2021-11-01 03:22:43

xman12 You should Ask this the Seller , not me. My Bltouch do work but not flawless. Sometimes the needle comes out and do not go inside the Bl-Touch again. After that the needle touch the Bed all the time and when the Extruder goes to the left side the needle goes down next to the left side of the bed. If the extruder then move to the right direction the needle will bend aside because it colide with the left side of the Bed. this happens sometimes after the bed was messured after more 4 or 6 times, sometimes this happens after it mesured the last testpoint upper right of the glasbet. Also there ist in bug in the Printer Firmware, if you manualy move the z axis into the menue (not z axis offset! but the Move menue) to move the extruder up a bit and then start the measure procedure it will measure correct but then collide with the glasbet and destroy the surface. I have not reconized the exact procedure to make this bug happen. It seems that the Printer do not correct set the Value of the Move Menue back to standard, or something else. I Have the Board 4.2.2 inside with the silent steppers.

2021-11-02 01:56:48 Βοηθητικός (0)
υποβάλλουν
Απαντήσεις (4)
Κιτ εκτυπωτή 3D Creality 3D® Ender-3 V2 αναβαθμισμένης έκδοσης Μέγεθος εκτύπωσης 220x220x250mm TMC2208/Ultra-ήσυχη 32-μπιτη προσαρμοζόμενη πλακέτα/Πλατφόρμα γυαλιού Carborundum/Τροφοδοτικό Mean Well/Νέα οθόνη 4.3 ιντσών με έγχρωμη διεπαφή χρήστη
US$378.35 US$329.00

Ερ: what is nozzle included?

Ερώτηση από Ginciuxzs επί 2021-10-24 11:31:55

xman12 Should be the 0,4mm nozzle.

2021-10-25 04:08:06 Βοηθητικός (0)
υποβάλλουν
Απαντήσεις (7)

Είστε ο ειδικός, μπορείτε να βοηθήσετε;

Σας προσκαλούμε ειλικρινά να εγγραφείτε στο email πρόσκλησης απάντησης!

Εάν εγγραφείτε, θα σας προσκαλέσουμε μέσω email για να απαντήσετε σε ερωτήσεις που έχουν οι άνθρωποι σχετικά με τα προϊόντα. Με την εγγραφή σας] θα κερδίσετε επίσης το "Χρήσιμο σήμα "! Μπορείτε να διαγραφείτε ανά πάσα στιγμή στη σελίδα ρυθμίσεων απορρήτου.

Βοηθήστε τους άλλους και γίνετε πιο ευτυχισμένοι!

  • Εγγραφείτε

Σχετικά με τα σήματα

Τα σήματα σχετίζονται με την κοινότητα και οι χρήστες κερδίζουν σήματα δημιουργώντας ποιοτικό περιεχόμενο, ολοκληρώνοντας αποστολές ή συμμετέχοντας σε ειδικές δραστηριότητες. Συγκεκριμένα άτομα θα έχουν επίσης το δικό τους αποκλειστικό σήμα.
Διευθύνων σύμβουλος

Το CEO Badge ανήκει μόνο στο αφεντικό του Banggood.

Τα σήματα που μπορείτε να κερδίσετε έρχονται σύντομα
  • Εντάξει

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • Εντάξει

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe