Ανταλλακτικό για το Drone αγώνων FPV URUAV UR65 - Σετ πλαισίου 65mm Κριτικές - Banggood Ελληνικά Online Shopping

Ανταλλακτικό για το Drone αγώνων FPV URUAV UR65 - Σετ πλαισίου 65mm

US$10.38
~~US$10.99~~
Αγορασε τωρα

Κριτικές πελατών

4.94 εκτός 5

Δείτε όλες τις κριτικές 947

5 αστέρι
903 (95.4%)
4 αστέρι
35 (3.7%)
3 αστέρι
6 (0.6%)
2 αστέρι
2 (0.2%)
1 αστέρι
1 (0.1%)

Γράψτε μια κριτική Λάβετε διπλούς πόντους κριτικής εάν είστε μία από τις πρώτες 3 κριτικές που δημοσιεύθηκαν!

Όλες οι κριτικές (947)
Εικόνα (138)
Βίντεο (0)
Όλα τα αστέρια
- Όλα τα αστέρια(947)
- 5 αστέρι(903)
- 4 αστέρι(35)
- 3 αστέρι(6)
- 2 αστέρι(2)
- 1 αστέρι(1)

Ταξινόμηση κατά:

Κορυφαία κριτική

Κορυφαία κριτική
Πιο χρήσιμο
Πρόσφατα

Κριτικές μόνο από τη χώρα σας (Greece)

|

Εμφάνιση πρωτότυπου

Ένα μέρος της κριτικής έχει μεταφραστεί αυτόματα.

Joseph DeguzmanVIP3
PH
06/06/2018

All three frames that I ordered were bent, so I had to let these simmer in boiling water to straighten them out. There is also one design flaw in these frames. The shafts for the ducts (prop guards) are positioned in a way that if you're using happymodel style motors, the heatshrink for the motor wires gets pushed up when the motor is mounted. This causes the heatshrink to press against the motor bell, which could seriously damage your motors, or, worse, blow up your esc.

All three frames that I ordered were bent, so I had to let these simmer in boiling water to straighten them out. There is also one design flaw in these frames. The shafts for the ducts (prop guards) are positioned in a way that if you're using happymodel style motors, the heatshrink for the motor wires gets pushed up when the motor is mounted. This causes the heatshrink to press against the motor bell, which could seriously damage your motors, or, worse, blow up your esc.

All three frames that I ordered were bent, so I had to let these simmer in boiling water to straighten them out. There is also one design flaw in these frames. The shafts for the ducts (prop guards) are positioned in a way that if you're using happymodel style motors, the heatshrink for the motor wires gets pushed up when the motor is mounted. This causes the heatshrink to press against the motor bell, which could seriously damage your motors, or, worse, blow up your esc.
29

Σχόλια

Εμφάνιση πρωτότυπου
BG521865790VIP3
US
24/04/2019

very hard frame. need it

very hard frame. need it

very hard frame. need it
7

Σχόλια (2)

Εμφάνιση πρωτότυπου

Show:

Σύνολο 0 σελίδες

Πήγαινε στην σελίδα

Πηγαίνω

Ίσως σας ενδιαφέρει

recommendation for you