Κριτικές πελατών

Γράψτε μια κριτική
  • Όλες οι κριτικές (227)
  • Εικόνα (21)
  • Βίντεο (1)
  • Όλα τα αστέρια
    • Όλα τα αστέρια(227)
    • 5 αστέρι(213)
    • 4 αστέρι(9)
    • 3 αστέρι(5)
    • 2 αστέρι(0)
    • 1 αστέρι(0)
Ταξινόμηση κατά:
Κορυφαία κριτική
  • Κορυφαία κριτική
  • Πιο χρήσιμο
  • Πρόσφατα
Κριτικές μόνο από τη χώρα σας (Greece)
|
Εμφάνιση πρωτότυπου

Ένα μέρος της κριτικής έχει μεταφραστεί αυτόματα.

  • 30/10/2018

    not an easy to start with package on itself, have to search google for how to make it work.

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 27/03/2020

    Αυτά τα είδη είναι καλής ποιότητας. Το Pcb είναι καλής ποιότητας, η συναρμολόγηση των ηλεκτρονικών εξαρτημάτων είναι καλοψημένη. Ο εξοπλισμός είναι πλήρης, τίποτα δεν λείπει, ακόμα και τα Τζάμπερ για να ρυθμίσουν την ταχύτητα των βηματοκινητήρων παρέχονται. Αυτή είναι μια πολύ καλή τιμή για την τιμή.

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 21/04/2019

    This CNC GBRL based driver board kit can control up to 3 stepper motors with the electrical components included. The main board has convenient pin headers to connect stepper motor leads and as many of the limit or other switches you might choose to adopt for your project. The jumpers seen under the stepper driver board location are for the adjustment to configure the stepper board. Default is often good enough. The use a of a Nano form of processor board makes it easy for me to swap with another one if I was testing a new firmware but wanted to keep old one I was comfortable with. Also I can decide to only place the quantity of steppers driver modules as needed. So if I only had one axis with a motor. I could save the other driver boards as spares. The plug fashion of module also allows debugging by swapping module components to see if fault moved with a particular module.

    Σχόλια (1)
    Εμφάνιση πρωτότυπου
  • 08/03/2018

    On my CNC shield V4, the STEP and DIR was not corresponding between the pin layout from the Android Nano and the step driver board. After switching both pin the bor start to work. Edit cpu_map.h file like below: #define X_STEP_BIT 5 // Uno Digital Pin 2 #define Y_STEP_BIT 6 // Uno Digital Pin 3 #define Z_STEP_BIT 7 // Uno Digital Pin 4 #define X_DIRECTION_BIT 2 // Uno Digital Pin 5 #define Y_DIRECTION_BIT 3 // Uno Digital Pin 6 #define Z_DIRECTION_BIT 4 // Uno Digital Pin 7 P/s: this fix apply for grbl 1.1 version, edit map pin in config.h file at the older version

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 02/01/2020

    Όλο το σετ έφτασε μια χαρά, ευχαριστώ!

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 12/11/2020

    tutto ok! l'unico problema il cavo!

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 05/02/2020

    some pins were bent. very cheap and works

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 06/01/2020

    Εξαιρετική κατάσταση. Πολύ χρήσιμο, ευχαριστώ!

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 10/07/2019

    good

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 25/03/2019

    good device ok

    Σχόλια
    Εμφάνιση πρωτότυπου
Show:

    Σύνολο 0 σελίδες

    Πήγαινε στην σελίδα

    recommendation for you
    • US$40.24
    • US$38.99
    • US$12.99
    • US$21.26
    • US$13.99
    • US$66.95
    • US$41.99
    • US$15.99
    • US$15.99
    • US$13.59
    • US$20.84
    • US$7.99
    • US$12.99
    • US$32.99
    • US$14.26
    • US$19.99
    • US$15.99
    • US$9.99