Κριτικές πελατών

Γράψτε μια κριτική
  • Όλες οι κριτικές (91)
  • Εικόνα (15)
  • Βίντεο (0)
  • Όλα τα αστέρια
    • Όλα τα αστέρια(91)
    • 5 αστέρι(78)
    • 4 αστέρι(11)
    • 3 αστέρι(2)
    • 2 αστέρι(0)
    • 1 αστέρι(0)
Ταξινόμηση κατά:
Κορυφαία κριτική
  • Κορυφαία κριτική
  • Πιο χρήσιμο
  • Πρόσφατα
Κριτικές μόνο από τη χώρα σας (Greece)
|
Εμφάνιση πρωτότυπου

Ένα μέρος της κριτικής έχει μεταφραστεί αυτόματα.

  • 09/05/2020

    Καλή μηχανή. Χρειάζεται κάποιες αναβαθμίσεις για να είναι τέλεια. Το συνιστώ σε όλους!

    Σχόλια (1)
    Εμφάνιση πρωτότυπου
  • 22/11/2019

    Fast delivery (6 days) from UK. Assembled in less than one hour. Printer works as expected, it was delivered without the glass plate and the aluminium print bed is not 100% flat, the middle is 0.1mm lower than the front and rear edge. (So only 4 stars for quality.) So far 4 out of 22 prints (20 are my own design) failed because of the print releasing from the bed during printing. I feel that is an acceptable result for someone new to 3D printing. I ordered the glass plate for the print bed and hope that will solve the prints releasing during printing.

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 01/06/2021

    The printer has been delivered well before the expected date, i.e. nearly a week in advance. Very good ! The packaging is professional, the molded foam makes sure that all parts remain in place and are not damaged. The packaging list checks with the contents, a few goodies are also present: a mouse pad, and a tool to remove the print from the heated bed when it is finished. The only remark I have on the packaging is that the the two extruders are in a foam pocket with the screws left loose in the same pocket. No missing part, fortunately :) Assembling the printer is a matter of a couple of hours. Some challenge to fix the Z axis as one has to insert the screws from below without a good view. My first screw escaped into the body of the printer and I was nearly panicking not to be able to get it back, but I was OK with it at the end. The test print at the end with a colour gradient is very convincing. I could even check the 'end of filament' sensor as the small amount of filament in the box is not enough to complete the test print. As far as I can judge after a few hours print, I heartily recommend this printer. The quality of the test print is high and the colour mix is beautiful. The machine is a bit noisy when idle (the cooling fan of the power supply is quite noisy), but the moves during printing do not produce too much noise. I like the control panel for local printing from the SD card; I still need to do the tests from a PC or a raspberry with Octopi. Definitely satisfied with my purchase!

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 12/05/2021

    j'ai bien reçu le colis, le carton est casser un.peu partout mais à l'ouverture je crois qu'il n'y a rien de casser, je verrai sa demain quand je le monterai. Merci PS: sous réserve

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 28/08/2020

    Great product. Easy to assemble and use. Some tuning of settings was required to get better prints. Quick delivery! One motor bracket was bent probably during transport but it could easily be bent back.

    Σχόλια (1)
    Εμφάνιση πρωτότυπου
  • 10/06/2021

    Είμαι ικανοποιημένος με το προϊόν, το έλαβα σε λιγότερο από μια εβδομάδα, καλά συσκευασμένο. Η συναρμολόγηση είναι πολύ απλή, μου πήρε 15-20 λεπτά να το στήσω και να το βάλω σε λειτουργία. Μετά από αναβάθμιση του δίσκου, έφτιαξα το πρώτο δίχρωμο κίτρινο και άσπρο αποτύπωμα (το αρχείο δοκιμής που παρέχεται στην κάρτα SD) το αποτύπωμα είναι υπέροχο. Ένας πολύ καλός εκτυπωτής με καλό δίσκο και ένα αποτύπωμα που είναι εφικτό σε 2 χρώματα σε μια όχι υπερβολική τιμή: συνιστώ.

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 05/02/2021

    Κόλις, εντάξει. Εντάξει

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 29/10/2019

    Дошёл из Китая в Харьков за 25 дней. Всё вроде цело, комплектация в порядке. Пока нет возможности собрать. Запущу - допишу отзыв!

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 01/07/2019

    Tengo muchos problemas de adherencia con la primera capa, no trajo el superplate y lo que trae para poner encima de la cama caliente es muy malo

    Σχόλια
    Εμφάνιση πρωτότυπου
  • 14/01/2022

    εκτυπωτής υπερ 3d

    Σχόλια
    Εμφάνιση πρωτότυπου
Show:

    Σύνολο 0 σελίδες

    Πήγαινε στην σελίδα

    Ίσως σας ενδιαφέρει

    recommendation for you
    • US$9.99
    • US$59.49
    • US$27.59
    • US$499.00
    • US$8.04
    • US$39.99
    • US$462.00
    • US$11.54
    • US$12.99
    • US$21.99
    • US$12.99
    • US$6.92
    • US$5.18
    • US$43.88
    • US$979.00