Ένα μέρος της κριτικής έχει μεταφραστεί αυτόματα.
Με πολύ καλές συστάσεις. Οι οδηγίες είναι λίγο σύντομες, αλλά επαρκείς. Με το Ender 3 Prow/ αναβαθμισμένο Creality 1. 5 σιωπηλή κεντρική μονάδα δεν είχα κανένα από τα θέματα που περιγράφηκαν από το TeachingTech φροντιστήριο. Έλαβα ένα αυθεντικό BLTC V3.1, και επίσης δεν είχα κανένα από τα προβλήματα του "BLTC V3 ασυμβατότητας w/ Ender 3". Η δημιουργικότητα είχε ανέβει στο επίπεδο μετά από όλα τα παράπονα για το άθλιο λογισμικό.
Works well on Ender 3, BUT if your control board has capacitor C7 installed (see photo) then you must remove it, or the very short duration Z-stop signal from BLTouch will not be detected and the extruder will just crash into the print bed when it auto-homes. This is a known issue with BLTouch and the latest Ender 3 control boards leave out C7. To refit the Ender 3/Pro cover and fan, you need to bend the four pins on the adapter PCB so that the 4-way header from BLTouch is horizontal. Versions of this kit sold elsewhere have the pins already bent.
Λειτουργεί μια γοητεία. Απαιτεί λίγη δουλειά για να στήσει, αλλά ακολουθώντας τις οδηγίες είναι αρκετά απλό. Οι οδηγίες δεν είναι καλές, αλλά υπάρχουν πολλά εξαιρετικά βίντεο στο διαδίκτυο (προτείνω το κανάλι "Διδασκαλία Τεχνών). Είναι πολύ εύκολο να εισάγετε κατά λάθος έναν από τους συνδέσμους εσφαλμένα (μια στήλη από τις καρφίτσες πάνω). Νόμιζα ότι ήταν το υλισμικό και έψαξα διάφορες αναθεωρήσεις λογισμικού πριν βρω το λάθος. Κατέβασα το τελευταίο λογισμικό και το έστησα σύμφωνα με τις οδηγίες του διαδικτύου. Τώρα το πρώτο μου στρώμα κατεβαίνει μια απόλαυση κάθε φορά χωρίς να χρειάζεται να ελέγχω το κρεβάτι με το χέρι με χαρτί. Δεν μπορώ να προτείνω αυτό το προϊόν πιο έντονα - κατηγορώ τον εαυτό μου που δεν παρήγγειλα τον εκτυπωτή με αυτή την επιλογή προεγκατεστημένη. Αν δεν έχεις αυτόματο ισοπεδωτή κρεβατιών, αυτή είναι η νούμερο ένα αναβάθμιση για να αγοράσεις πριν από οτιδήποτε άλλο.
This works great! No more spinning the wheels over and over again to level my bed before 3-D printing. The install is a little bit tricky but there are lots of online instructions and videos to help you. highly recommended.
Works great on original CR-10 (V1). I did struggle with flashing, so use official website with latest version. https://www.creality.com/download/bl-touch-firmware_c0006 I had great results with flash: latest CR-101.1.6BLTouchV3.1PowerLossContinueEnglish.hex Just make sure sure that fuse settigs are D6, DC, FD (as described in manual) Also, do not that you will have to remove z-limiter wiring, and do manual z-offeset settings..
Kit for the ender 3 with all that you need to install it. nice box. The product complies as described in the add. I received V3.1
Αυτό είναι το σωστό σετ για το Ender 3. Περιέχει το BLT, το βραχίονα στερέωσης και καλώδια. Περιέχει επίσης το απαιτούμενο κιτ για την αναλαμπή του πίνακα ελέγχου σας. Το δικό μου ήταν με το BLTC v3.1.
Προιόν Σέμα που αγοράστηκε από το Ταμίλναντου του Τσενάι. Θέλει 2 μήνες να φτάσει στην περίοδο Κορόνα.
This product arrived within 2 weeks of ordering it. For international delivery I am very impressed. The item itself is really well packaged. It is complete, and appears to be of good quality. My printer is currently mid print so I have not had a chance to install it, but as this is a genuine item I have no doubts it will function perfectly.
Got BL Touch V1.3 for Creality V1 mainboard. It is relatively easy to install (Ender 3), once installed and enabled in the firmware it works as expected. The only drawback of this solution is that the Pinboard A (pin expansion for BL Touch) does not really fit into the mainboard enclosure when connected to all the cables as it is too high and conflicts with the fan. It is also worth to remember to add auto-leveling commands to the slicer output code.